Plumbing 101: A Necessity for Bathtub Installation
Plumbing 101: A Necessity for Bathtub Installation
Blog Article
What are your insights and beliefs about A Step-by-Step Guide to Installing a Bathtub?
Setting up a bathtub isn't precisely rocket science, yet it does need strong plumbing, woodworking, and in some cases, tiling abilities. Replacing an old tub with a brand-new one is additionally a reasonably difficult project. If the old bathtub is conveniently obtainable, the job can move quickly; if you have to open a wall to eliminate the old bathtub as well as place the new tub, the job is a lot harder. In either situation, the project is within a residence handyman's skills, although you will certainly need an assistant to move out the old bathtub as well as embeded in the brand-new one. See to it you have certified yourself for the job and also fit trying it. As opposed to working with a service provider to take control of a halfway-completed task, it is better to think about utilizing one prior to you begin. Possibilities are you may require an expert plumber to make tube connections.
This article will certainly aid you install a brand-new tub in your restroom if you have actually already bought a brand-new bathtub and also do not require to change the arrangement of your previous water supply pipes.
Your tools and product list need to comprise the following:
Planning for the Installment
Firstly, the sustaining framework supplied with the bathroom ought to be fitted (if required) according to the maker's instructions. Next off, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is important to see to it that if the tap comes with a plastic washing machine, it is fitted between the bathroom and the taps. On a plastic bath, it is likewise practical to fit a supporting plate under the faucets unit to prevent stress on the tub.
Fit the versatile faucet connectors to the bottom of both faucets making use of 2 nuts and olives (often supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet via the hole in the bath. Use the nut supplied by the producer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. See to it you use every one of the supplied washing machines.
Connect the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bath should now be ready to be fitted in its final setting.
Removing Old Taps
If you need to change old faucets with new ones as a part of your installation, after that the first thing you must do is detach the water supply. After doing so, switch on the faucets to drain any water continuing to be in the system. The process of getting rid of the existing taps can be quite bothersome due to the restricted access that is usually the situation.
Make use of a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipelines to the taps. Have a fabric all set for the continuing to be water that will come from the pipes. As soon as the supply pipes have actually been gotten rid of, utilize the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to stop the single taps from transforming throughout this procedure. As soon as the faucets have been eliminated, the holes in the bath/basin will have to be cleaned up of any type of old securing compound.
Prior to moving on to fit the new faucets, compare the pipe links on the old faucets to the new faucets. If the old taps are longer than the new taps, then a shank adapter is required for the brand-new taps to fit.
Installing the Bath tub
Using the two wood boards under its feet, put the bath tub in the required setting. The wood boards are helpful in equally spreading out the weight of the tub over the location of the boards as opposed to concentrating all the weight onto 4 tiny points.
The next objective is to make sure that the bath tub is leveled all round. This can be attained by examining the level as well as changing the feet on the tub till the level checks out level.
To set up faucets, fit all-time low of the outermost versatile tap adapter to the suitable supply pipeline by making a compression join; after that do the same for the other tap.
Switch on the water system and examine all joints and brand-new pipework for leakages and also tighten them if needed. Fill the tub and additionally check the overflow outlet as well as the regular electrical outlet for leaks.
Ultimately, repair the bathroom paneling as defined in the manufacturer's user's manual. Tiling and also sealing around the bathtub should wait up until the bath tub has actually been used at the very least once as this will certainly resolve it right into its last placement.
Fitting New Touches
If the tails of the new taps are plastic, then you will certainly need a plastic port to prevent damages to the thread. One end of the port fits on the plastic tail of the tap and also the various other end provides a connection to the existing supply pipelines.
If you require to fit a monobloc, after that you will certainly call for decreasing couplers, which links the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next off, place the tap in the installing hole in the bath/basin making sure that the washing machines are in location in between the tap and also the sink. Secure the tap in place with the supplier provided backnut. Once the tap is safely in position, the supply pipelines can be linked to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with regular faucet ports. The former kind must be attached to the tap ends initially, tightening up only by hand. The supply pipes can later be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Bathtub
In the area where the bath satisfies the tile, it is required to secure the accompanies a silicone rubber caulking. This is essential as the installation can relocate enough to fracture a stiff seal, causing the water to penetrate the wall surface between the bathroom and the tiling, leading to difficulties with moisture and also feasible leaks to the ceiling below.
You can select from a range of coloured sealers to blend in your fixtures as well as fittings. They are offered in tubes as well as cartridges, as well as are capable of sealing voids as much as a width of 3mm (1/8 inch). If you have a bigger void to load, you can load it with twists of soaked paper or soft rope. Remember to always fill the bath tub with water before sealing, to permit the motion experienced when the bathtub remains in use. The sealant can split fairly early if you do not take into account this motion prior to securing.
Additionally, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are additionally quickly offered on the marketplace. It is a good idea to fit the tiles utilizing water-resistant or water resistant adhesive and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As an enthusiastic reader about A Step-by-Step Guide to Installing a Bathtub, I assumed sharing that chunk was important. Sharing is nice. Who knows, you may just be helping someone out. Thanks a lot for your time. Visit us again soon.
Dial, we deliver! Report this page